Model APSC. Owners 24 Hour Timed Start Setup, Operation, and Use 23 of this manual has a section for the particular features and options installed in. Save this Book to Read prestige apsc installation manual PDF eBook at our Online Library. Get prestige apsc installation manual PDF. AUDIOVOX APSC INSTALLATION MANUAL — | PDF | 73 Pages | KB | 09 AUDIOVOX APSC INSTALLATION MANUAL The key.
|Country:||Trinidad & Tobago|
|Published (Last):||21 March 2008|
|PDF File Size:||20.59 Mb|
|ePub File Size:||16.71 Mb|
|Price:||Free* [*Free Regsitration Required]|
PART Select a mounting location inside the passenger compartment up behind the dashboard. You can enter Bank 3 from Bank 2 by turning the ignition key off then on after you’ve made the changes you wanted in Bank 2, Siren two Long ChirpYou can also go right to bank 3 by: Route this wire through a grommet in the firewall to the siren location. These modules are used to access a variety of features in the vehicle which can be as simple as door trigger inputs, to more complex door locks outputs, or transponder interfaces for remote starting.
Enter text innstallation picture: Page 30 For technical support go to www. To connect to the key in sensor circuit as shown for method 2: To print the manual completely, please, download it.
Aps c Installation Manual
Page 10 12 White Wire: Page 27 b 27 of Wps997c Neutral Start Switch from starting in gear. Connect this wire to the vehicle’s parking light feed wire. Parking Light Flasher Output This wire is the normally open contact of the on board parking light flash relay. Parking Light Flasher Input This wire is the common contact of the on board parking light flasher relay.
Page 22 Mechanical Neutral Start Switch from starting in gear. Audiovox 2 button remote security nanual with anti-hijack feature owners manual 14 pages.
PLATINUM APSC INSTALLATION MANUAL Pdf Download.
See owners manual for turning this feature on from the transmitter. Got it, continue to print. The Superheterodyne Receiver Antenna Assembly provided with this unit allows routing from below the dash board for maximum operating range.
Locate the control wire that connects the drivers door pin switch to the key in sensor switch. Multi Coil Adaptor Optional Information.
If this wire is not used or you have difficulty accessing the glow plug preheat circuit, you may elect to utilize the Diesel timed output as specified in Remote Start feature selection 9. Don’t have an account?
Be certain that the chosen mounting location will not inhibit any of the controls of the vehicle. Page 24 To connect to the key in sensor circuit as shown for method 2: Monitoring The Vehicle’s Engine: In this application, the Red wire of the door lock harness provides a ground pulse during the arming sequence, or pulsed ground lock output.
If there is a Non Plug in Shock Sensor used with the alarm system and it is not shunted during the Remote Start activation period, then vibration from the running vehicle can cause the alarm to trigger. This wire will show 0 volts when the key is turned to the “OFF” Failure to connect this wire to the ignition switch side of the of the neutral safety switch can result in personal injury and property damage. To achieve optimum performance the coil signals must be evenly distributed.
By pressing ‘print’ button you will print only current page. Special considerations must be made for windshield glass as some newer vehicles utilize installarion metallic shielded window glass that will inhibit or restrict RF reception. Page of 32 Go.
Temperature Start Programming And Information. Comments to this Manuals Your Name. Enter text from picture: Understanding the difference between a mechanical and an electrical Neutral Start Switch will allow you to properly identify the circuit and select the correct installa- tion method.
These applications require the use of additional components which may include relays, fixed resistors, or for convenience, a Door Lock Interface. This is accomplished by first mapping out the firing order of the engine in groups of as indicated below.
Platinum APS-997C Installation Manual
Comments manuual this Manuals Your Name. Ignition 2 Output Connect this wire to the ignition 2 wire from the ignition switch. Page 12 21 Light Blue Wire: After you apw997c confirmed the operation of the Audiovox Remote Start unit and tested all the safety features of the system: Connect the Red wire inshallation the low current ground signal wire from the factory door lock switch to the factory door lock relay.
The unit will monitor the voltage level of the battery during remote start, wait for the voltage to drop while cranking, then look for the voltage level to go above the level it was before the vehicle began to crank which indicates the vehicle is running. Page 7 when used and the neutral safety switch as shown in the following diagram.
Don’t have an account?